UPVC Window Handle Replacement

Replacing a damaged window handle is a easy process, and UPVC Window Handle Replacement with the right tools it can be done quite quickly. It is important to know your type of handle and the spindle's length prior buying an alternative.

Older uPVC windows have handles with cockspurs, which have spurs that protrude to the lock of a wedge cockspur striker plate. These can be left- or right-handed and must be matched when replacing.

What type of lock or handle do you have? I have

There are a myriad of window locks and handles made from upvc each with its particular advantages and uses. The kind of handle you choose will determine how easy it is to open your windows and if the locking mechanism functions in the way you want it to. As time passes and with regular use, upvc window handles may become damaged or worn out, rendering them less secure and efficient. In some cases they may even fall off completely. If you notice that your upvc window handles have been removed, it's crucial to repair them as quickly as you can. This will help to avoid burglaries and ensure your home is secure.

The good news is that replacing your window handles made of plastic is a relatively simple task that can be done by everyone. With just a few tools and the right knowledge, this is a simple procedure that should take no longer than a couple of minutes. To begin, you will need to determine the type of lock and handle you have on your window made of upvc to help you identify the best replacement.

Inline Espagnolette Handles

They are the most popular kind of upvc handle and are typically located on the outside of your window. They have a flat design and come with an opening that is connected to the locking mechanism on the frame of the window when it is turned. Inline upvc handles also come with a spindle that runs through the centre of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have distinct hook-shaped designs. Cockspur handles are fitted with a single screw that holds the handle to the window frame and aren't as secure as other kinds of window handles.

Tilt and Turn Handles

In contrast to other upvc handles, tilt and UPVC Window Handle Replacement turn handles can be rotated to open the window and the handle can be tilted to the side to allow ventilation. They feature a 7mm spindle in the back and are available in right and left-handed versions.

It is crucial to determine the size of the spindle when purchasing a replacement upvc window handles handles made of upvc. There are a few that are the exact same size. To test the length of your handle made of upvc, simply drop something into the middle of the hole and then measure how far down it goes before meeting an obstruction. This is the largest spindle size that will fit in your windows.

What is spindles?

uPVC window handles operate similarly to doors. By turning the handle, you are able to activate a latch inside the frame. The window is then opened and shut. The handles can become damaged, especially if frequently used or exposed to harsh conditions. This can leave you needing to replace your uPVC windows handles as they might not be able to operate the window correctly for a long time.

There are many different kinds of uPVC handles that are available, including Espag, Cockspur and Spaded handle options. They are designed to fit in the uPVC frames in various ways. Each handle uses a specific spindle to lock the mechanism fitted to the window. This is why it is crucial to identify the kind of handle is installed on your uPVC window to find the right replacement for it.

The base section of the handle will inform the type of uPVC it is. A snap-in covers should be over the screw that holds the base of the handle in position. Take it off and you should be able see the second holding screw on the opposite side of the base portion of the handle. After both screws are removed you should be able to pull the handle away from the uPVC window.

Once you have removed the uPVC window handle you need to carefully unscrew the spindle that was previously attached to the locking mechanism. Be sure to note the length of the spindle since you'll need to make sure that you buy a replacement window glass that has the same length as your original handle and locking mechanism.

The spindle wears out and is unable to operate the locking mechanism. This could be due to corrosion, damage due to continuous use, or even a loosening locking mechanism. If this occurs, you will have to replace both the window handle and locking mechanism in order to restore the full functionality of your uPVC Windows.

How do I remove my old handle?

Over time and through everyday use, window handles may be damaged or destroyed, and if this happens it is crucial to repair them as soon as possible to ensure the security of your home. It is easy to replace a worn or damaged handle. The job can be completed in under one minute without the need of special tools.

The first step in removing the handle that was previously used is to remove the screw situated on the top of the base of the handle. After this screw is removed, the handle can be removed from the base section. Another screw will be located at the base of the handle. This too can be removed. Once these two screws are removed, the handle can be removed from the window's base.

Once the old handle is removed, grab the new handle and line up the fixing holes with the holes that are currently in the window frame. There might be a small cap or sticker on the new handle, so remove them if needed and then put the handle in the frame. It is essential to ensure whether the handle functions after it has been installed. Turn the handle over and make sure the lock mechanism is working.

Espag handles have spindles that protrude out of the handle and slot into the multipoint locking mechanism on the window frame. Cadenza windows come with a blade with cutouts which fit into the lock mechanism. Cockspur handles are long and hook over the outer frame of the window or the transom crossmember of the bar.

Once you have the new handle in place, slide the spindle inside the window lock and then tighten it. Once the handle is firmly fixed, replace the'snap in' cover and screw cap (if appropriate). Once the handle is ready to use, simply open and close the window a couple of times to ensure it works properly and securely.

How do I put in the new handle?

It's not difficult to change the handle on your windows made of uPVC. The process is easy. All you require is a screwdriver, and a small amount of patience. First, ensure that the handle is not locked. Remove any visible screws. You can also replace them using screw caps. Once the handle is removed and you are ready to take a note of the length of the spindle that extends from the back of the handle. This is crucial since it will determine the type of handle you'll require to purchase.

Espagnolette handles on uPVC are the most sought-after kind of handle. They feature a spindle that is connected to the handle and operates a locking mechanism within the frame of the window. Once the handle is turned it opens the latch on the window and allows it to open. During regular use and over time, espagnolette handles may become damaged.

Cadenza handles are a second type of uPVC window handle, which is typically used on tilt and turn windows. They have a protruding blade that operates the multipoint locking mechanism inside the window. They are more secure than espagnolette handle as they can only open from the inside. They can be replaced using the same procedure as you would do for handles made of espagnolette, but make sure the new handle is angled, not flat.

Once you have determined the correct handle to purchase, you can simply align the new handle with the existing screw holes, and then screw it in the appropriate position. After that, you should put the screws back on and verify that your new handle is operating properly. This is done by moving the handle from the locked position to the unlocked and then back to the locked position a few times. If you experience any issues, it could be worth contacting a specialist to see if they are able to help resolve the problem. They can provide advice on how to resolve the issue in a quick and effective way.