Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they do not corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will prevent unnecessary repair costs as well as improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home, and could even be fatal. It is essential to take the time to make sure that you are doing everything you can to ensure that your windows are in good repair.

For single pane windows, it is fairly easy to replace them, and the new window will usually fit inside the old frame very easily. However, if windows with double panes are anchored by internal beading it will be more difficult to remove the existing panes and install new ones. In this instance it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.

If you are going attempt to remove the window panes yourself it is crucial to wear the appropriate safety equipment that includes gloves with a thick layer of material and eye protection. It is also recommended to lay down a dropcloth prior to you begin working on the window panes so that any shards fall on the fabric and not on the floor, where they could be trampled under.

Once the glass has been removed, it's a good idea to seal the gap with clear packaging tape or duct tape to prevent water and drafts from entering the home until a professional comes out and repair the window. This also serves as an obstruction to prevent criminals from getting into your home. If the gap is large, you may think about the security door with an integrated window as it offers the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. However, over time they are susceptible to a range of problems including sagging. A sagging uPVC windows could cause issues with light, draughts and even security. It's important to take action immediately if you notice your uPVC windows are sagging.

To fix a sagging window you can try repositioning the hinges. First, you'll need to open the windows so you can access the frame. Then, using a screwdriver, you can unscrew the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have moved your hinges. If you're satisfied with the fit, tighten the screws to ensure they stay in place.

If you aren't able to move the hinges, you might require replacing the seal. Rubber seals may dry out and lose their elasticity over time, which causes them to lose their tightness. If this happens, it's crucial to replace the seal as quickly as possible so that your uPVC windows are waterproof and safe from drafts.

uPVC handles could also loosen. Most often it is due to screws that have become loose over time. However, it can be due to the fact that the handle mechanism has been worn out. Fortunately, it's easy to repair the handle of a window that is loose yourself. The first step is to close the window and perform a test to ensure that it fits. The joints at the corners of the sash should align with the joint on the casing. If it isn't then you can make use of a screwdriver to loosen the handle and turn the mechanism back into its original position.

3. Water Leaks

It is important to act if you awake each day to discover mouldy walls and wet floors. Water leaks through windows can cause structural damage to your home and affect your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Based on the severity of the issue the caulking that was used up may require removal before a new layer of caulk can be applied. When it is time to uPVC repair, you must be careful not to over-caulk. This can make your window harder to clean and lower its energy efficiency.

It is essential to ensure that any drainage holes are free of debris and that the sill pan has been angled properly so that it drains away from the window. In more serious instances, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives in damp conditions and is able to quickly spread throughout the house.

If the leakage is occurring between the double glazing repair Woking-glazed glass it is more likely that the issue is with the seal than the frame. Again this can easily be fixed by an uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open, or if it opens with an ease. These are easily replaced by any competent DIYer and are usually done within a few minutes.

Almost every household in the UK will have top-hung or side hung uPVC windows that have hinges and like any mechanical part they will wear out over time. Changing a window hinge is essentially a simple procedure, but it is easier to do if you have someone to assist in holding the frame up.

Make sure that the uPVC hinges are closed and open in the correct direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The issue could be caused by opening the window improperly or a faulty installation in the factory. Sending us a photo via our website is often enough to resolve the problem. We are always happy to offer assistance.

Regularly lubricating the hinges is also necessary. Applying a light engineering lubricant on the hinges is an ideal way to do this. We recommend using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. The ideal time to do this once a year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different factors. The hinges, also due to wear and tear can become misaligned, this will cause a gap to form between the sash and the frame. These can be easily repaired by giving them a good cleaning, but in the event that they are beyond repair it may be necessary to get them re-aligned or replaced. Secondly the interlock, this is on the hinge side of the window repairs Kettering, can also be misaligned, and again it's feasible to give them a clean but in certain cases, it may be necessary to have them replaced.

The second most frequent reason for draughts is window seals, these can become worn down or damaged over time and let air escape through these gaps. Replacement of these with high-quality weatherstripping is a good way to stop draughts. Another option is to replace the window with low-emissivity glass, this will help to regulate indoor temperatures and will reduce draughts.

The last way to reduce drafts effectively is to use a draught-excluder. These are usually made of fabric tubes filled with a filler, which can be hung over your window sill. They can help block out cold air and keep your home warm and cozy!

With a bit of regular maintenance and repairs your windows made of upvc will continue to provide excellent security and insulation for your home. However, it is important to recognize that windows last for window Repairs Kettering a certain period of time and they may reach an point at which it is more efficient to replace them than repair them. So, if you are having issues with your upvc windows, it is always recommended to seek help from a professional as soon as you can.