Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. In contrast to aluminium and timber, they do not corrosion or rot.

It is essential to clean and oil UPVC doors and windows on a regular basis. This will reduce unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it could cause a large amount of damage to your home, which can make it very hazardous and possibly fatal. It is important to ensure that your windows are in good condition.

For single pane windows, it is relatively easy to replace windows, and the new one will usually fit inside the frame that was previously installed easily. If windows with double panes are joined by internal beading, it is harder to remove and replace the panes that were previously in use. In this instance, you will need to locate some plastic spacers that help the new pane to fit properly into the window frame.

If you're planning to attempt to remove the glass panes yourself, it is essential to wear the proper safety gear, including thick gloves and protective eyewear. It is also an excellent idea to lay down a dropcloth before you start working on the glass, so that any fragments of glass fall on the fabric instead of onto the floor, where they could be trodden under and cause further damage.

Once the glass is removed from the window, it's best to seal the gap with clear packaging tape or duct tape to stop water and upvc repair drafts from entering the property until a professional can come out and fix the window. It also acts as a barrier to prevent any intruders from getting into your home. If the gap between the window and the door is substantial, you may want to use an alarm system that has a window. This will provide the best of both.

2. Sagging

uPVC is durable and energy efficient alternative to timber sash window. In time, they could develop a variety of issues such as sliding. A sagging window can cause problems with light, draughts or even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from becoming worse.

To repair a window that is sagging, you can try repositioning the hinges. First, you'll need to unblock the windows to reach the frame. Then, remove both the hinges at the top and bottom with a screwdriver and adjust them counter-clockwise or clockwise. Once you've repositioned the hinges, close your window and test it for fitting. If you're satisfied with the fit, you can tighten the screws until they stay in place.

If you cannot reposition the hinges, you could have to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to loosen. If this happens, it's crucial to replace the seal as quickly as possible to ensure your uPVC windows are watertight and safe from drafts.

uPVC handles can also loosen up. Often, this is caused by screws that have come loose over time. However, it could also happen because the handle mechanism has been worn out. It's relatively simple to fix a loose uPVC handle. First, you'll need to shut the window and do a test fitting. The corner joints of the sash must be aligned with the casing joint. If it does not, you can use the screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

It is crucial to take action if get up each morning to discover mouldy walls and wet floors. Leaks of water from windows can cause structural damage to your home and affect your ability to regulate the temperature inside your home. Most often, upvc window repairs window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be completed by any skilled DIYer. Depending on how serious the issue is, the old caulking may need to be removed. When it comes to upvc repair [this content], you must avoid over-caulking. This can make your window more difficult to clean and decrease its energy efficiency.

Verify that the drainage holes have no debris inside them and ensure that the sill pan has been angled correctly to drain away from the window. In more severe cases, you may need to replace the window.

Other indicators of water leakage include sills that are rotten and the appearance of black spots of mold on the walls near the window. This fungus thrives under damp conditions and can spread quickly throughout the home.

It is also important to note that if the leak is coming from between the glass of your double glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sliding. This can be easily fixed by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be the reason if your uPVC window is difficult to open, or if it opens with an ease. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Like any mechanical component hinges are prone to wear out over time. It's very simple to replace a hinge on a window but it's much simpler if you have someone to help hold the frame.

Verify that the uPVC hinges are open and uPVC repair closed in the proper direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The problem can be caused either by opening the window doctor improperly or a faulty installation in the factory. This issue can be fixed by sending us a photograph via our website and we will be happy to give you suggestions.

Regularly lubricating the hinges is essential. Applying a light engineering lubricant on the hinges is a great method of doing this. We suggest using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and reduce the risk of sticking. Ideally, you should do this once a year. WD40 and other solvent-based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different factors. Firstly the hinges, again due to wear and tear may become displaced, which can cause a gap to form where the sash joins the frame. If they're beyond repair, it could be necessary to have them realigned. Second, the interlock can also become misaligned. This happens on the hinge's side, and might require to be cleaned. In some cases it is possible to replace the hinges.

The second most frequent cause of draughts is the window seals, these are prone to wear or damaged over time, and will allow air to escape through the gaps. Installing high-quality weatherstripping will help to prevent draughts. Replace the upvc windows with low-emissivity glass. This will help to regulate indoor temperatures, and reduce the risk of draughts.

Lastly, one of the most effective ways to reduce draughts is by using a draught excluder. These are usually fabric tubes which are filled with a kind of filler. They can be positioned on the windowsill on top. These will keep your home warm by blocking cold air.

Your windows made of upvc will keep providing excellent insulation and security to your home with a little regular maintenance and repairs. However, it is important to recognise that all windows have a life span and eventually, they will reach a point where it is more economical to replace them than repair them. If you encounter any issues with your Upvc window it is recommended to speak with a professional as soon as you can.