Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are long-lasting, durable and easy to maintain. They don't decay or upvc window repairs rust as aluminum or timber.

It is crucial to wash and oil UPVC doors and windows regularly. This will prevent unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and even be fatal. You should take the time to make sure that your windows are in good shape.

For single pane windows it can be relatively simple to replace them, and the replacement is usually able to fit into the frame of the previous one easily. If you have double glazed window repairs near me-paned windows which are held together by internal beading, it will be harder to remove and replace the panes that were previously in use. In this case you'll need locate some plastic spacers to aid the new pane in being able to fit correctly into the frame of the window.

If you plan to attempt to remove the window panes by yourself, it is essential to wear appropriate safety gear, including thick gloves and eye protection. It is also recommended to lay down a drop cloth before you begin working on the glass so that any shards fall onto the cloth instead of onto the floor, where they could be trampled upon and cause further damage.

After the glass has been removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional comes out and fix the window. It also acts as a barrier that will prevent any intruders to gain access to your home. If the gap between the door and the window is large, you might prefer security screens that has an opening. This will give you the best of both.

2. Sagging

Upvc windows and doors are a cost-effective, durable and energy-efficient alternative to timber windows made of sash. However, over time, they may be afflicted by a variety of issues, including sagging. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from worsening.

Repositioning the hinges can help fix a window that is sliding. First, you'll need to open the windows so you can get at the frame. Then, remove both the top and bottom hinges with a screwdriver and adjust them clockwise or counter-clockwise. Close your window to test the fit after having repositioned your hinges. If you're satisfied with the fit of your window, you can tighten screws to secure them in the right position.

If you are unable to reposition the hinges, you may need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, leading them to loosen. It is important to replace your seal as quickly as you can in order to keep your uPVC window waterproof and draughtproof.

UPVC handles can also become loose. Often, this is caused by screws that have become loose over time. However, it could also happen because the handle mechanism has been worn out. Luckily, it's not difficult to repair the loose uPVC window handle yourself. First, you'll need close the window and perform an experiment to ensure that it fits. The joint at the corners of the sash must align with the joint on the casing. If it isn't, you can use a screwdriver or a wrench to loosen the handle and return the mechanism to its original position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains, it is important that you take action. Water leaks through windows can cause structural damage to your home and also impact your ability to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be done by any DIYer who has the ability. Depending on the severity of the problem is, the old caulking may have to be removed. It is essential to keep in mind that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk' as this will only make the area harder to clean and decrease the efficiency of your energy usage.

It is important to check that any drainage holes are free of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more serious situations, you may need to think about replacing the window.

Mold spots and rotten sills are also signs of water leakage. The mold thrives in damp environments and can quickly spread across the house.

It is also important to remember that if the leak originates from the glass of your double glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sliding. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open with ease, it may be the hinges that are at fault. Any competent DIYer can replace hinges in just a few minutes.

Like all mechanical parts hinges will be damaged over time. It's very simple to change the hinges on a window but it's much simpler if you have someone to help you to hold the frame.

Make sure that the uPVC hinges are closed and open in the correct direction. You can check this by checking for the arrows on each hinge, this shows which way the window should be opened.

The problem can be caused due to opening the window in the wrong way or due to a poor installation at the factory. This can often be resolved by sending us a photograph on our website. We will be more than happy to give you advice.

It is also crucial to grease the hinges regularly. This can be done by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. It is recommended to do this at least once a year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by different things. The hinges may also become unbalanced due to wear, creating a gap where the sash meets frame. If they are beyond repair, it could be necessary to get them re-aligned. Secondly the interlock, this is located on the hinge of the window, may also be misaligned, and again it may be possible to give them a clean but in certain cases, it may be necessary to get them replaced.

The seals may wear out or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help regulate indoor temperatures and lessen draughts.

One of the most effective ways to cut down on drafts is to use an draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be positioned on the top of your windowsill. These will keep your home warm by blocking cold air.

With a little maintenance and repair your windows made of upvc will continue to provide an excellent level of security and insulation for your home. It is important to remember that all windows eventually wear out and it could be cheaper to replace them instead of fixing them. If you are experiencing issues with your upvc window you should consult a professional as soon as possible.