Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like timber and aluminum.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will help prevent unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and may even be fatal. It is important to take the time to ensure that you're doing all you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace and generally fit into old frames very easily. However If you have double pane windows that are secured by internal beading it will be more difficult to get rid of the panes that are in place and replace them with new ones. In this situation it is essential to purchase plastic spacers in order to make sure that the new pane fits into the window frame.

Wearing eye protection and heavy gloves is a must for anyone who plans to remove the glass yourself. It is also recommended to lay down a dropcloth before you start working on the glass to ensure that any shards fall on the fabric instead of landing on the floor, where they could be trampled upon and cause further damage.

It's a great idea to cover the gap with tape after the glass has been removed. This will keep water and drafts from entering your home until a professional arrives to repair the window. It also acts as a barrier to prevent any criminals from getting into your home. If the gap is particularly large, you may think about an alarm door that comes with an integrated window as it offers the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable, durable and energy-efficient alternative to timber windows with sash. However, with time, they can suffer from a variety of issues, including sliding. A sagging window in uPVC can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's crucial to act fast to prevent the problem from becoming worse.

To repair a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll need to open the window so that you can get to the frame. Then, using a screwdriver, you can take off the hinges on the top and Upvc Repair bottom and adjust them by turning them clockwise or anti-clockwise. Once you've adjusted the hinges, close your window and verify the fit. If you are happy with the fit of the window, you can tighten screws to hold them in place.

If you cannot reposition the hinges, you might have to replace the seal. Over time, rubber seals lose their elasticity and dry out and cause their tightness to decrease. It is crucial to replace your seal as quickly as you can to keep your uPVC window waterproof and draughtproof.

uPVC handles may also loosen. Often, this is caused by screws that have come loose over time. However, it can also happen because the handle mechanism has been worn out. Fortunately, it's easy to repair the loose uPVC window handle yourself. First, you'll need close the window and then perform an experiment to ensure that it fits. The corners of the sash must be aligned with the casing joint. If it does not you can use a screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains, it's crucial to take action. Water leaks from windows can not only cause degrading of the structure of your home but also undermine your efforts to control the temperature in your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is a relatively easy fix that can be completed by any skilled DIYer. Based on the severity of the issue the caulking that was used up may need to be removed before a fresh layer is applied. When it comes to upvc repair; visit this page,, you should avoid 'over-caulking'. This can make your window more difficult to clean and lower its energy efficiency.

It is important to check that the drainage holes are clear of debris and that the sill pan has been angled in a way that allows it to drain away from the window. In more serious cases you might have to consider replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage is occurring between the double-glazed glass it is more likely the problem is with the seal rather than the frame. This can be easily repaired by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open with ease it could be hinges at fault. They can be easily replaced by any competent DIYer and are usually done within a few minutes.

Like any mechanical component, hinges can be damaged over time. It's easy to change the hinges on a window but it's much simpler if you have someone to help hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the right direction. Check for the arrows on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window a certain manner or because of improper installation in the factory. It is usually possible to fix the issue by sending us a photograph via our website and we will be happy to give you advice.

Regularly lubricating the hinges is also necessary. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window to operate and close more easily. It also decreases the chance of windows getting stuck and stop corrosion. Ideally, you should do this once a year. WD40 and other solvent-based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different things. The hinges can also be unbalanced due to wear, creating an opening between the frame and sash. These can be easily repaired by giving them good cleaning, but in the event that they are beyond repair it could be necessary to get them re-aligned or replaced. The interlock, which is located on the hinge side of the window and can also become misaligned, again it's possible to just give them a good clean, but in certain cases, it may be necessary to have these replaced.

These seals can wear down or become damaged over time, allowing air to escape. Installing high-quality weatherstripping is a good way to prevent draughts. Replace the windows made of upvc with low-emissivity glasses. This will help to regulate indoor temperatures and decrease the possibility of draughts.

The final method to cut down on the amount of draughts is to use a Draught-excluder. These are typically fabric tubes filled with a filler that can be placed over your window sill. These will help to keep cold air out and keep your home warm and cozy!

With a little maintenance and repair windows made of upvc will continue to provide a great level of security and insulation for your home. It is important to remember that all windows eventually wear out and it is more cost-effective to replace them rather than repair them. So, if you're experiencing issues with your Upvc windows, it is recommended to seek assistance from a professional as soon as you can.